IsItAGoodCar
Reliability Guide

Common Problems with the
1968 Austin 1100 / 1300 (ADO16)

We've identified 3 known issues that can affect the 1968 Austin 1100 / 1300 (ADO16). 1 of these are serious faults that could be expensive to repair.

3
Known Issues
1
Serious
2
Moderate
0
Minor

All Known Issues

Sill, floor and radius-arm mount corrosion

SeriousBodywork & Rust

British Classic Cars puts it plainly: rust is the whole conversation on the ADO16, and the survivor you view has either been properly restored at the known rot points or will need to be. The cars dissolve from the sills, subframe mountings, floors, inner wings and the notorious rear radius-arm mounts, while Old Classic Car's period recollection — footwells all-but gone on a terminally rusted 1100 — shows how the damage presents in real UK use. The Hagerty feature on the 1100 Club records how a 1985 Practical Classics buying piece titled 'BMC's Best-Selling Rot Box' helped trigger the club's founding as numbers fell fast. Repair sections exist but structural welding is the real cost, so the buying rule is condition before specification, and a documented dry-stored car is worth every premium asked.

Est. Repair Cost: £400-£1,500+ per affected area for competent welding and sections
Warning Signs:

Bubbling paint along the bottom of the doors and outer sills, Soft or perforated floor pans under the carpets, Cracked or flaky metal at the rear radius-arm mounts and subframe fixings, Fresh underseal applied unevenly, hiding repaired patches

What to Inspect:
  • Lift carpets and inspect floor pans and inner sill lips with a torch and probe
  • Check the rear radius-arm mounts and subframe mounting areas for cracking and filler
  • Treat a resprayed car with suspicion — inspect underneath for patch quality
  • Compare against the 1100 Club's registers and technical database before buying a project
Verified by IsItAGoodCar Research TeamUpdated

Leaking Hydrolastic displacers and pipework

ModerateSuspension & Chassis

The interconnected Hydrolastic system — Alex Moulton's fluid-spring debut that gave the 1100 its magic-carpet ride — is also its age-related weak point. Units corrode, hoses perish and the cars sag at a corner or drop ride height, and replacement is a specialist job: Hydrolastic and Hydragas Service Ltd sells re-hosed, derusted and leak-tested BMC ADO16 front displacers at £175 with a £150 core surcharge and a one-year unlimited-mileage warranty, plus ready-assembled suspension pump kits at £130, because no factory provision existed to maintain these 60-year-old units. British Classic Cars confirms displacers are serviceable by the marque specialists rather than cheaply swapped, and the club's expertise is the practical route for keeping wet-suspension cars legal and level.

Est. Repair Cost: £175-£500+ for re-hosed displacer units and pipework by a Hydrolastic specialist
Warning Signs:

Car sits nose-down or low at one corner, Fluid weeping at the displacement units or fine-bore pipes, Uneven or bouncy ride that worsens as pressure drops, Pitted, rusty displacers when looked under the car

What to Inspect:
  • Confirm the car stands level at all four corners, with Hydrolastic displacers dry and undamaged
  • Look for replacement hoses or patches and ask whether units have been recently re-hosed and tested
  • Check the specialist route and core-return terms before assuming new units are off-the-shelf
Verified by IsItAGoodCar Research TeamUpdated

A-series wear, carburettor faults and poor starting when damp

ModerateEngine

The shared 1098cc and 1275cc A-series with SU carburettors is robust and cheap, but as Old Classic Car notes early 1100s were not famous for reliability, and tired examples smoke, run sluggishly and idle rough when carburettor needles wear and timing drifts. The marque guides' standard advice is to check what engine is actually fitted — 1100 and 1300 units swap easily between cars — and to expect the Mini world's upgrades underneath. On damp UK mornings the classic ADO16 complaint is a car that starts and stalls, or simply won't fire, from perished wiring and poor earths rather than any big mechanical failure, so an electrical check and fresh points, condenser and plug leads are routine recommissioning.

Est. Repair Cost: £150-£500 for carburettor overhaul and full ignition recommissioning
Warning Signs:

Acrid blue smoke on pull-away or after idling at lights, Sluggish performance that improves slightly when the engine warms, Cracking and backfire on overrun from weak mixture, Starting only after a push or repeated priming

What to Inspect:
  • Confirm the engine capacity and specification against the chassis number, since swaps are common
  • Inspect SU carburettors for worn linkage and check the timing for slack distributor parts
  • Test on a wet day and check earth straps, bullet connectors and the condition of the wiring
  • Verify the condition of fuel lines, tank strap and pump, with the electric pump partly in the boot on later cars
Verified by IsItAGoodCar Research TeamUpdated

Buying Tips for 1968 Austin 1100 / 1300 (ADO16)

  • Check for corrosion at the sills, subframe mounting points, floor pan, inner wings and the rear radius-arm mounts — these are the rot points the marque guides name, and structural repair is the real cost.
  • A Hydrolastic car should sit level, hold its height and not sag at a corner; displaced units can be re-hosed and tested by specialists, but budget £175-£350 for the units and pump kit if yours are leaking or long-since removed.
  • Confirm the engine matches the car: 1100 and 1300 units swap easily, and upmarket Riley, Wolseley and Vanden Plas trim is the scarce fitting, so buy from club registers where possible.
  • Factor in a welder's rate (£40-£60 per hour at a good independent) before bidding on a project; these cars are cheap to buy and expensive to fix badly, which is why condition commands big premiums.
  • For road use, ask whether the car runs on lead substitute or has hardened valve seats cut into the head, as pre-1989 A-series heads can recede their seats on sustained unleaded motorway running.