IsItAGoodCar
Reliability Guide

Common Problems with the
2011 Tesla Roadster

The 2011 Roadster 2.5 update introduced revised front styling with aggressive cooling vents, a rear diffuser, improved sound deadening, and updated interior switchgear.

What changed for 2011

  • •Roadster 2.5 facelift bringing new front fascia with directional diffuser vents and rear lower diffuser
  • •Redesigned supportive sport seats with upgraded lumber cushioning and revised leather upholstery
  • •Push-button transmission gear selector replacing the earlier mechanical gear lever
  • •Optional 7-inch Alpine touchscreen infotainment system with integrated reversing camera
  • •Improved sound deadening and thicker cabin insulation reducing wind whistle at motorway speeds

Common MOT watch-outs

  • !Suspension anti-roll bar drop-link play from stiff Ohlins damper settings on rough UK asphalt
  • !Uneven tyre shoulder wear on rear Yokohama performance tyres from aggressive factory camber
  • !Brake caliper slider sticking caused by road grime accumulation during winter storage
3
Known Issues
2
Serious
1
Moderate
0
Minor

All Known Issues

Energy Storage System (ESS) Parasitic Drain and Battery Pack Bricking

SeriousElectrics & Electronics

The first-generation Roadster lacks the deep-sleep low-power hibernation states engineered into modern electric vehicles. Continuous parasitic current draw from the Vehicle Management System (VMS) and auxiliary cooling pumps drains the 53 kWh battery pack if left unplugged. If state-of-charge drops to 0%, individual lithium-ion cells drop below critical voltage thresholds, causing irreversible internal chemical breakdown, sheet undervoltage lockouts, and refusal of the onboard charger to engage. Recovering a bricked pack requires high-voltage DC revival by specialists or a full battery rebuild.

Est. Repair Cost: £2,500–£22,000
Warning Signs:

Vehicle completely dead and unable to power on or unlock via key fob, Charge port LED does not illuminate when charging cable is connected, Instrument cluster display shows persistent Sheet UnderVoltage or BSM alerts, Onboard charger fails to initiate power transfer from domestic or 32A wallboxes

What to Inspect:
  • Verify vehicle state-of-charge immediately and confirm it has been continuously plugged in during storage
  • Request a battery diagnostic health log file from a recognized EV specialist showing cell sheet balancing
  • Confirm the onboard cooling fans spin up normally when the vehicle is connected to a live charger
Verified by IsItAGoodCar Research TeamUpdated

Power Electronics Module (PEM) Inverter and IGBT Component Degradation

SeriousElectrics & Electronics

The Power Electronics Module (PEM) converts high-voltage DC battery power into variable-frequency three-phase AC power for the induction motor. Over prolonged exposure to heat cycles, road grime sucked through cooling ducts, and component ageing, the PEM's internal IGBT power switching transistors, DC bus capacitors, and gate drive boards degrade. This causes the car to throw drive inverter faults, enter severe limp-home mode with reduced power, or completely refuse to drive. Specialist bench rebuilding with upgraded cooling blowers and modern silicon components is necessary.

Est. Repair Cost: £2,000–£4,800
Warning Signs:

Instrument cluster displays PEM Overheat or Drive Disabled warning alerts, Sudden loss of propulsion power while accelerating onto dual carriageways, PEM cooling blowers running constantly at maximum audible speed even when idling, Intermittent failure to select Drive or Reverse from stationary

What to Inspect:
  • Listen for abnormal PEM cooling blower whining or buzzing from behind the seats
  • Check service history invoices for documented PEM cleaning, capacitor updates, or rebuilds
  • Perform sustained acceleration runs to ensure no inverter temperature fault triggers
Verified by IsItAGoodCar Research TeamUpdated

Lotus-Derived Suspension Ball Joint and Wishbone Bush Wear

ModerateSuspension & Chassis

Built upon the lightweight Lotus Elise extruded aluminium chassis architecture, the Tesla Roadster carries a substantial weight penalty due to its 450 kg battery assembly, bringing total kerb weight to nearly 1,240–1,300 kg. This extra mass accelerates wear on the front and rear upper and lower ball joints, anti-roll bar drop links, and rubber wishbone bushings when driven across demanding UK road surfaces. Worn joints result in clunks over road imperfections, vagueness in steering precision, uneven tyre wear, and MOT failure for excessive suspension movement.

Est. Repair Cost: £450–£1,100
Warning Signs:

Audible knocking or clunking sounds from front or rear wheel arches over potholes, Looseness or vagueness in high-speed steering precision around motorway bends, Uneven feathering or inside shoulder wear on front and rear tyres, MOT failure notice for excessive play in suspension ball joints or track rod ends

What to Inspect:
  • Jack up the car or inspect on a ramp to test for play in upper and lower ball joints using a pry bar
  • Examine rubber boots on all suspension joints for splits, perishing, or grease leakage
  • Test drive over speed bumps and rough asphalt to listen for suspension thuds or rattles
Verified by IsItAGoodCar Research TeamUpdated

Buying Tips for 2011 Tesla Roadster

  • Prioritise 2.5 models for their significantly quieter cabin and superior push-button gear selector ergonomics
  • Check whether the car received the optional 80 kWh 3.0 battery upgrade package
  • Test the push-button gear selector for positive engagement between Drive, Reverse, and Park